LucidPro Daily Loss Limit: Soft Breach vs Max Loss
Learn the difference between LucidPro’s soft daily loss restriction and hard maximum-loss breach, with a practical risk checklist and AUDIT offer.
Yash R
· Updated
LucidPro uses two separate risk controls: a daily loss limit (DLL) that Lucid describes as a soft breach, and a maximum loss limit (MLL) that can end the account. Hitting the DLL restricts additional trading until the next session; reaching the MLL is the hard account breach.
Applicable coupon offer: use code AUDIT for 30% off participating LucidPro purchases. LucidDaily has a separate recorded 40% scope. Confirm the selected plan and reduction at checkout. Coupon verified on 12 October 2026.
LucidPro is a futures program. Its limits should not be applied to a CFD prop account.
Soft and hard controls compared
| Control | What it measures | Result when reached |
|---|---|---|
| Daily loss limit | Loss within the current trading session | Trading restriction until the next session |
| Maximum loss limit | Total loss against the active trailing floor | Account breach |
| Profit target | Evaluation progress | Passing still requires every other rule |
| Consistency | Distribution of profit | Can delay a payout or completion calculation |
The DLL does not replace the MLL. A trader can be stopped for the day without losing the account, but a trade that also reaches the active MLL can still close it.
Read the full Lucid Trading audit for the plan overview.
What Lucid means by a soft DLL breach
Lucid’s official LucidPro article states that all daily loss limits are soft breaches. When the DLL is reached:
- New trading is restricted for the remainder of the session.
- The account is not lost solely because the DLL was touched.
- Trading may resume in the next session if the MLL remains intact.
- Open positions and platform behavior should not be assumed to protect the account from the MLL.
A soft restriction is not permission to ignore the level. A fast market can move through both thresholds before a trader reacts.
Why the maximum loss limit is different
LucidPro uses an end-of-day trailing maximum-loss system. The floor is tied to the highest closing balance and can move upward after profitable sessions. Once the stated locking point is reached, the floor stops trailing.
That creates three distinct states:
- Below the DLL: trading can continue within the other rules.
- At the DLL but above the MLL: the trader is restricted until the next session.
- At the MLL: the account is breached.
Intraday unrealized profit does not move an end-of-day floor in the same way that a real-time trailing drawdown would. However, realized losses, commissions and open-equity movement still affect available room during the session.
Risk-room calculation
A practical dashboard calculation is:
current account value − active MLL = remaining maximum-loss room
Separately calculate:
session DLL threshold − current session loss = remaining daily room
Use the smaller of the two as the binding risk constraint.
Example
Assume the dashboard shows:
- Current account value: $51,250
- Active MLL: $50,200
- Remaining maximum-loss room: $1,050
- Remaining daily room: $600
The daily control is tighter at that moment. A new trade should not be sized as if $1,050 were fully available. Commissions and slippage also consume part of the cushion.
This is an illustration, not a statement of a specific account’s dollar limits. Use the figures displayed for the purchased size.
What resets and what does not
The DLL restriction clears with the next trading session under Lucid’s policy. The MLL follows a different path:
- It can trail upward after a higher closing balance.
- It does not drop back merely because a new day starts.
- It may lock after the plan’s stated threshold is reached.
- A payout or losing session can reduce the distance between account value and the floor.
This is why “the daily limit resets” should never be interpreted as “all risk room resets.”
Pre-trade checklist for LucidPro
Before entering a position:
- Record the current account value.
- Record the dashboard’s active MLL.
- Check the session DLL status.
- Include open P&L and commissions.
- Convert the planned stop distance into dollars.
- Add a slippage allowance.
- Confirm total open risk is below both remaining limits.
- Reduce or stop trading before the platform restriction becomes the risk plan.
The firm’s automatic control is a final boundary, not a substitute for a trader-defined stop.
How code AUDIT applies
For participating LucidPro orders:
- Coupon:
AUDIT - Recorded LucidPro reduction: 30%
- LucidDaily recorded scope: 40%
- Rule effect: none
A careful checkout sequence is:
- Verify the product says LucidPro.
- Select the account size and connection.
- Enter
AUDIT. - Confirm the displayed 30% reduction.
- Save the account’s DLL and MLL table.
- Recheck the dashboard values before the first trade.
Do not assume the 40% LucidDaily scope applies to LucidPro.
Common mistakes
Treating DLL as the only loss rule
The MLL can be closer than the daily threshold after a payout or losing period.
Confusing a soft breach with no consequence
The account may remain open, but trading is restricted for the session.
Using evaluation target as risk capital
The displayed account size is not the amount available to lose. Drawdown is the relevant operating boundary.
Ignoring fees
Commissions and other trading costs reduce the cushion even when the chart price has not reached the planned stop.
Bottom line
LucidPro’s DLL pauses trading for the session, while the MLL is the hard account boundary. Track both values and let the smaller remaining cushion control position size. Code AUDIT provides 30% off participating LucidPro purchases; the separate 40% LucidDaily scope should not be carried across plans.
Official sources checked
Related Prop Firm Audit guides
FAQ
Frequently Asked Questions
Not by itself. Lucid says its daily loss limits are soft breaches that restrict new trading until the next session, provided the maximum loss limit has not also been reached.
Reaching the active maximum loss limit is the hard breach. Traders must monitor both the session loss restriction and the trailing maximum-loss floor.
The trading restriction applies until the next session. The maximum-loss threshold follows its separate end-of-day trailing method and does not simply reset each day.
Use code AUDIT for 30% off participating LucidPro purchases. LucidDaily has a separate recorded 40% scope, so confirm the selected product and checkout total.